standard test method for softening point of bitumen

10.2 Bitumen Softening Test 10.2.1 General

An alternative to the penetration test for checking the consistency of bitumen, is the ring and ball softening point test. The scope of this test is to provide a method for determining the consistency of semi-solid and bituminous materials in which the sole or major constituent is either bitumen or tar pitch. 10.2.1.2 Definition.

9 TEST TO CHECK QUALITY OF BITUMEN FOR USE IN ROAD

Sep 11, 2015 · Fig-3 shows Softening Point test setup. Also Read:Softening Test Procedure of Bitumen. Fig-3 Softening Point Test Setup 4. Specific Gravity Test. The specific gravity of bitumen is defined as the ratio of mass of given volume of bitumen of known content to the mass of equal volume of water at 27 0 C. The specific gravity can be measured using AASHTO T 53 - Standard Method of Test for Softening Point January 1, 2009 Standard Method of Test for Softening Point of Bitumen (Ring-and-Ball Apparatus) This test method covers the determination of the softening point of bitumen in the range from 30 to 157°C (86 to 315°F) using the ring-and-ball apparatus immersed in distilled water (30 to 80°C

ASTM D3461 - 18 Standard Test Method for Softening Point

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard. ASTM Standards. A314 Specification for Stainless Steel Billets and Bars for Forging. D36 Test Method for Softening Point of ASTM D36 / D36M - 14(2020) Standard Test Method for 1.1 This test method covers the determination of the softening point of bitumen in the range from 30 to 157 °C [86 to 315 °F] using the ring-and-ball apparatus immersed in distilled water [30 to 80 °C] or USP glycerin (above 80 to 157 °C). 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents;

ASTM D36/D36M - Standard Test Method for Softening

Standard Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus) This test method covers the determination of the softening point of bitumen in the range from 30 to 157°C [86 to 315°F] using the ring-and-ball apparatus immersed in distilled water [30 to 80°C] or ASTM D36/D36M - Standard Test Method for Softening Point Standard Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus) This test method covers the determination of the soft-ening point of bitumen in the range from 30 to 157°C (86 to 315°F) using the ring-and-ball apparatus immersed in distilled water (30 to 80°C),

ASTM D36/D36M :Standard Test Method for Softening Point

ASTM D36/D36M, 2014 Edition, July 1, 2014 - Standard Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus) This test method covers the determination of the softening point of bitumen in the range from 30 to 157 °C [86 to 315 °F] using the ring-and-ball apparatus immersed in distilled water [30 to 80 °C] or USP glycerin (above 80 to 157 °C). ASTM D36/D36M :Standard Test Method for Softening Point ASTM D36/D36M, 2014 Edition, July 1, 2014 - Standard Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus) This test method covers the determination of the softening point of bitumen in the range from 30 to 157 °C [86 to 315 °F] using the ring-and-ball apparatus immersed in distilled water [30 to 80 °C] or USP glycerin (above 80 to 157 °C).

ASTM D36Gilsonite Softening Point

Gilsonite Softening Point Standard Test Method(ASTM D36). This test for Gilsonite is completely matches with the test for bitumen that is described below and its based on the standard ASTM D36.. This test method covers the determination of the softening point of bitumen in the range from 30 to 157°C (86 to 315°F) using the Ring-and-Ball apparatus immersed in distilled water (30 to 80°C ASTM D5 / D5M - 20 Standard Test Method for Penetration 2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.. ASTM Standards. D8 Terminology Relating to Materials for Roads and Pavements. D36/D36M Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus). D244 Test Methods and Practices for Emulsified Asphalts

ASTM E28 - Standard Test Methods for Softening Point of

NOTE 1-For testing asphalts, tars, and pitches, see Test Method D36. Test method using the automated ring and ball softening point apparatus is the reference method and the test method using the manual ring and ball method is an alternative method. The values stated in SI units are to be regarded as the standard. ASTM-D36 Standard Test Method for Softening Point of 1.1 This test method covers the determination of the softening point of bitumen in the range from 30 to 157°C (86 to 315°F) using the ring-and-ball apparatus immersed in distilled water (30 to 80°C), USP glycerin (above 80 to 157°C), or ethylene glycol (30 to 110°C). 1.2 The values stated in SI units are to be regarded as the standard.

Bitumen Tests- Tests of Bitumen- Bitumen Lab Tests

Softening point Ring and Ball method (EN 1427) This method, under European standard EN 1427, serves to test the behaviour of bitumen at elevated service temperatures. The temperature is determined at which a layer of bitumen, in a brass ring, experiences a certain deformation under the weight of a steel ball as the temperature rises. DETERMINATION OF SOFTENING POINT STANDARD DETERMINATION OF SOFTENING POINT STANDARD IS:1205 1978. DEFINITION Softening point is the temperature at which the substance attains a particular degree of softening under specified conditions of test. APPARATUS Standard Ring and Ball Apparatus. Steel balls 2 No, each 9.5mm in diameter and weighing 3.5 + 0.05 grams.

DIME - Print Sample Report

Test Method:ASTM D36-141:Standard Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus) (Softening Point) Verified Date :09/25/2020 Date Tested :09/24/2020 Determining Softening Point Of BitumenThis test is done to determine the softening point of asphaltic bitumen and fluxed native asphalt, road tar, coal tar pitch and blown type bitumen as per IS:1205 1978. The principle behind this test is that softening point is the temperature at which the substance attains a particular degree of softening under specified condition of the test.

Determining Softening Point Of Bitumen

This test is done to determine the softening point of asphaltic bitumen and fluxed native asphalt, road tar, coal tar pitch and blown type bitumen as per IS:1205 1978. The principle behind this test is that softening point is the temperature at which the substance attains a particular degree of softening under specified condition of the test. Exp 12 Softening Point of Bitumen - Civil Engineers PKEXPERIMENT NO. 12 SOFTENING POINT OF BITUMEN (RING-AND-BALL APPARATUS). [ASTM Designation:D 36-76, AASHTO Designation:T 53-89]SOFTENING POINT:Softening Point of Bitumen. The softening point is defined as the mean of the temperatures at which the bitumen disks soften and sag downwards a distance of 25 mm under the weight of a steel ball.

Exp 8 Penetration Test of Bitumen - Civil Engineers PK

PREPARATION OF TEST SPECIMEN. Heat the sample with care, stirring when possible to prevent local overheating, until it has become sufficiently fluid to pour. In no case should the temperature be raised to more than 90 °C above expected softening point for petroleum asphalt (bitumen). Do not heat samples for more than 30 minutes. List of Tests for Bitumen as per Indian Standard » Civil Generally, higher softening point indicates lower temperature susceptibility and is preferred in the hot climate. The following figure Softening Points Test Setup. For details procedure and calculation, check out my article on Softening Point Test Of Bitumen As Per IS:1205-1978.

PENETRATION TEST OF BITUMEN IS 1203-1978 - Civil

Jul 21, 2020 · Avoid overheating bitumen. While the needle is penetrating into the sample, if there is any movement of the container, that determination shall be discarded. Take care of the temperature as per standard. Read more :Method of Softening point test of bitumen Ring-Ball Test for Softening Point of Bitumen, Asphalt and The softening point of bitumen or tar is the temperature at which the substance attains particular degree of softening. As per IS:334-1982, ASTM E28-67 or ASTM D36 or ASTM D6493 11, it is the temperature in ºC at which a standard ball passes through a sample of bitumen in a mould and falls through a height of 2.5 cm, when heated under

SOFTENING POINT OF BITUMEN (IS:1205:1978) -

May 12, 2013 · Objective For determination of softening point of a given bitumen. Reference Standards IS :1205-1978-Indian standard methods for testing tar and bituminious materials (Determination of softening point) Equipment & Apparatus Ring and Ball apparatus, Steel balls Brass rings Ball guide Support Thermometer Bath with stirrer Procedure Sample material is heated to a SOFTENING POINT OF BITUMEN (IS:1205:1978) - May 12, 2013 · Objective For determination of softening point of a given bitumen. Reference Standards IS :1205-1978-Indian standard methods for testing tar and bituminious materials (Determination of softening point) Equipment & Apparatus Ring and Ball apparatus, Steel balls Brass rings Ball guide Support Thermometer Bath with stirrer Procedure Sample material is heated to a

Softening Point Test Of Bitumen » Introduction, Apparatus

Softening Point test of bitumen is done to determine the consistency of bitumen. This test gives an idea of the temperature at which the bitumen attain certain viscosity. Softening point is defined as the temperature at which bitumen softens beyond some arbitrary softness i.e. bitumen softens and sags down about 25mm below the weight of steel ball. Softening point test of bitumen- Step by Step Procedure Procedure Softening point test of bitumen At first the sample of bitumen is heated above 70 degree centigrade to 100 degree centigrade above the softening point. Now take glass plate and prepare a mix of glycerin and Dexedrine. Apply this mixture to the surface of glass to prevent bitumen from sticking.

Softening point test of bitumen- Step by Step Procedure

Softening point of bitumen = (A + B)/2 = (46 + 47)/2 = 46.5 degree centigrade. Significance of Softening point test of bitumen. The softening point of bitumen used in the pavement construction varies between 35° to 70°.It indicates how susceptible the bitumen Standard Test Method for Penetration of Bituminous the expected softening point for tar pitch in accordance with Test Method D36, or to more than 90°C above it for petroleum asphalt (bitumen). Heat samples for the minimum time neces-sary to ensure that they are sufficiently uid. Stir to ensure that the sample

Standard Test Method for SOFTENING POINT OF BITUMEN

ASTM D2398, 1982 Edition, 1982 - Standard Test Method for SOFTENING POINT OF BITUMEN IN ETHYLENE GLYCOL (RING-AND-BALL) There is no abstract currently available for this document Order online or call:Americas:+1 800 854 7179 Asia Pacific:+852 2368 5733 Europe, Middle East, Africa:+44 1344 328039 Standard Test Method for Softening Point of Bitumen 1.1 This test method covers the determination of the soft- ening point of bitumen in the range from 30 to 157°C [86 to 315°F] using the ring-and-ball apparatus immersed in distilled water [30 to 80°C] or USP glycerin (above 80 to 157°C). 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard.

Standard Test Method for Softening Point of Bitumen

D 3461 Test Method for Softening Point of Asphalt and Pitch (Mettler Cup-and-Ball Method)5 E 1 Specication for ASTM Thermometers6 3. Summary of Test Method 3.1 Two horizontal disks of bitumen, cast in shouldered brass rings, are heated at a controlled rate in a liquid bath while each supports a steel ball. The softening point is reported as the Standard Test Method for Softening Point of Bitumen Scope 1.1 This test method covers the determination of the soft- ening point of bitumen in the range from 30 to 157°C (86 to 315°F) using the ring-and-ball apparatus immersed in distilled water (30 to 80°C), USP glycerin (above 80 to 157°C), or ethylene glycol (30 to 110°C). 1.2 The values stated in SI units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety

Standard test method (ASTM D36) for Softening point of

Oct 28, 2017 · 1. This method is useful in determining the consistency of bitumen as one element in establishing the uniformity of shipments or sources of supply. 2. melting point is the temperature at which the bituminous binders have an equal viscosity (i.e. the consistency of all the grades will be same at the softening point e.g. if two samples have softening points of 30 °C and 80 °C respectively Standard test method (ASTM D36) for Softening point of Oct 28, 2017 · 1. This method is useful in determining the consistency of bitumen as one element in establishing the uniformity of shipments or sources of supply. 2. melting point is the temperature at which the bituminous binders have an equal viscosity (i.e. the consistency of all the grades will be same at the softening point e.g. if two samples have softening points of 30 °C and 80 °C respectively

exp-10 - Experiment No 10 Standard Test Method For

Experiment No. 10 Standard Test Method For SOFTENING POINT OF BITUMEN (ASTM D 36-86) Purpose:This test method covers the determination of softening point of bitumen in range from 30-80 C using the ring-and-ball apparatus immersed in distilled water. Apparatus Required:1 Rings - Two square-shouldered brass rings conforming to the standard dimensions 2 Pouring Plate - A flat, Standard Test Method for Softening Point of Bitumen (Ring 1.1 This test method covers the determination of the softening point of bitumen in the range from 30 to 157 °C [86 to 315 °F] using the ring-and-ball apparatus immersed in distilled water [30 to 80 °C] or USP glycerin (above 80 to 157 °C). 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard.

Leave a Comment